6/15/2023 0 Comments Milwaukee right angle drill![]() The only suggestion he would make is if you are buying this tool, get one with an extra battery so there is no down time.ĭan wanted to use the tool in action and show me under the hood of my GMC truck taking off bolts in tight spots. ![]() We never did get a good shot, but we can pass along that Bill had a lot of fun using this tool and was happy for once not having to drag around his corded angle drill for the day. We were going to show you the videos, but I am sure you didn’t want to see a video of his thumb in front of the camera lens. After he came back all proud of his work and told us he had some great videos, we had to take a look. Bill know his tools, but Bill doesn’t know technology. We had another day we gave it to Bill to video him drilling some holes in joists for wiring. Now the drill is not an impact drill, but we were able to remove some nuts and do a lot of tightening of screws and nuts. We tried to get some good video of this, but it’s hard to get a good camera angle when Ty’s arm is hiding the work. With summer coming up, a lot of people are getting their boats ready for summer and what better place to use this drill in tight spots then a tight engine compartment of a boat. We even lent it out for a couple of days, we gave the drill to our friend down at the marina. We had the drill for a week and put it to good use. With the placement of the switch, this makes working in tighter spots much easier.Īll in all we found the performance of the drill just as good as the overall design of the tool. This is the beauty of the paddle switch since when we are working in tighter spots, sometimes we cannot always grip a tool the right way and even sometimes need to use two hands. We could be very precise in matching the speed to our work and also keeping a steady speed at all times. The paddle switch is nice and long and we found it very easy to control the speed whether or not we used the top, middle or bottom of the paddle switch to operate the drill. The paddle switch is what operates the drill to start the drill spinning. The paddle switch is a great design for this tool. We found the drill very easy to control and maneuver in almost any circumstance.Īs you know working in tight spots can be very challenging, since there is not a lot of room for the tool and your hand. The grip, the head length, tool length and weight makes this a great drill to have on hand when you need to get into tight spots. The overall weight of the tool isn’t bad either weighing only 4.25 lbs. Also the length of the tool is shorter than most coming in at 11.25”. Speaking of small areas, the head on the drill is only 3.75” long so you are able to get into tighter spots. The over molded grip helps provide extra grip control, which is always a key when working in small areas. Now thinking about it and the design of the tool, it’s basically a long rod, so we guess the balance should be good compared to a standard drill. Once you pick up the drill, the first thing we noticed was that the balance of the tool is great, it just feels right in your hand. The battery slides onto the bottom of the drill as you can see in the pictures.įirst looking at this drill you would think the balance would not be great. The drill is powered by 1 18V Lithium-ion XC Redlithium battery. This clutch operates the 3/8” single sleeve ratcheting head chuck. The system is equipped with an electronic clutch which provides 11 different settings and one drill mode. When your drill is maxed out or clutched out, a red led light will flash to let you know that this event happened. Another feature is the red LED on the front of the drill. Sometimes we have seen LED lights that do not do much except show a shadow, so we were extremely please how bight and efficient this light is, partly because of the small head on the drill. On the front of the drill there is a nice LED work light that helps the user see what they are doing in dark locations. In the kit it comes obviously the drill which is model 2615-20, a 1 hour charger, 1 XC Lithium-ion battery and a carrying case. The model number of this kit is 2615-21.Īs stated this is the right angle drill kit model number 2615-21. It includes an innovative electronic clutch which delivers precise torque to your project. It packs a lot of power, technology and can fit into the tightest of spaces. Well Milwaukee has something for you, the 2615-21 Right Angle Drill. Don”t you hate when you cant fit your drill in a tight area and the smaller drills just wont cut it.
0 Comments
Leave a Reply. |